Dremel 2500 User Manual download pdf

For use with 1/2” or less sand-

ing and grinding stone acces-

sories only.

Attachment for use with Dremel Rotary Tool

Models 100, 200, 300, 400, 4000, 770, 800,

275, 285, 395, 398.

The guide comes completely assembled and

ready to use for sanding and grinding applica-

tions up to ½” ( 13 mm) thick.

Router bits are not allowed for

use with the Sanding/Grinding

Guide attachment.

Sanding/Grinding Guide Attachment

Installation instructions:

Step 1: Remove the housing cap A from the

end of the tool and set housing cap aside. The

original housing cap must be reinstalled when

this attachment is not used (Fig. 1).

Step 2 & 3: Loosen the collet nut and place your

accessory in and tighten. Note: The attachment

is for ½” diameter accessories or smaller.

Please refer to the owner's manual for proper

collet nut assembly instructions and accessory

operation instructions.

When inserting a bit into your

Dremel Rotary Tool be sure

that the bit is securely inserted into the collet. Al-

ways use the wrench to tighen the collet nut to

prevent the bit from loosening within the collet.

Do not use the Dremel Chuck.

Step 4: Thread the attachment B onto the

threaded portion of the housing collar C (Fig. 2).

Step 5: Adjust the attachment B to the desired

depth by loosening the wing knob D (Fig. 3).

Using the Sanding/Grinding Guide

Attachment

The guide has a 90 and 45 degree bevel for var-

ious sanding applications. The tool with the

guide attached can be taken to a secure work

piece or can be stationary in the Dremel Multi-

Vise.

Installation instructions to Dremel

Multi-Vise:

The tool with the guide attached can be taken

to a secure workpiece or can be stationary in the

Dremel Multi-Vise 2500-01 (Sold Separately).

Step 1: Set up Dremel Multi-Vise on secure

workbench. Place the tool holder into the

Dremel Multi-Vise according to Dremel Multi-

Vise instructions.

Step 2: Place tool with accessory secure

through the tool holder F (Fig. 4).

Step 3: Hold the Sanding/Grinding Guide B firm

and thread onto front end of tool until tightly

secure (Fig. 4).

Step 4: The guide can be adjusted from the 90

degree side to the 45 degree side by loosening

the wing nut D and sliding the attachment B off

the cylinder E (Fig. 5).

Step 5: Turn the attachment B 180 degrees and

slide the attachment B onto the cylinder E and

tighten wing knob D at desired depth (Fig. 5).

Read and understand the manual for the use of the tool with this accessory.

SAVE THESE INSTRUCTIONS

WARNING

Sanding/Grinding Guide Attachment Model A576

WARNING

CAUTION

FIG. 1

FIG. 2

FIG. 3

2610958467 04/09 Printed in Mexico

P.O. Box 1468

Racine, Wisconsin 53401

1-800-437-3635

http://www.dremel.com

FIG. 5

FIG. 4

DM 2610958467 04-09:DM 2610958467 04-09 4/22/09 12:52 PM Page 1

1 2

1-800-437-3635 1

Summary of Contents

Page 1 - 1-800-437-3635

For use with 1/2” or less sand-ing and grinding stone acces-sories only.Attachment for use with Dremel Rotary ToolModels 100, 200, 300, 400,

Page 2

Pour emploi avec des acces-soires de ponçage et derecti-fication de 1/2 po ou moins.Complément conçu pour emploi avec les outils rotatifsDremel modèle

Dremel 2500 User Manual

Browse online or download User Manual for Power tools Dremel 2500. Sanding/Grinding Guide Attachment Model A576 1-800-437-3635

Summary of Contents

More documents for Power tools Dremel 2500

Comments to this Manuals

Dremel 2500 User Manual

Browse online or download User Manual for Power tools Dremel 2500. Sanding/Grinding Guide Attachment Model A576 1-800-437-3635

Summary of Contents

More documents for Power tools Dremel 2500

Comments to this Manuals

Related products and manuals for Power tools Dremel 2500